Skip to the page

Our cookies help keep the site secure, hold your basket for you, count visits and tell us which ads lead to orders. Privacy policy

5% off every kit at checkout: use

5% off kits:

Basket
Menu
Search
Guides

How to Fit CCTV at Home: Plan, Wire, Drill and Seal

Plan the whole job first: camera spots, recorder position, PoE or coax wiring, cable routes, a bench test, then drilling and sealing.

By CCTV Kit Direct team4 min read

To fit CCTV at home, plan the whole job before you pick up a drill: choose the camera spots, decide where the recorder will live, measure each cable route, test the kit on a table, then drill and seal. The wiring decides most of the work. A PoE (network) kit needs one Cat6 cable from each camera to the recorder, while a coax kit needs a video cable and a power lead for each camera, plus a mains socket near the recorder for its power supply. This guide covers the planning and the cable work; for the app and recorder set-up, see our guide to setting up a CCTV camera kit.

1. Choose the camera spots

List the places you want covered, usually the front door, the drive, the back door and any side access, and mark each one on a sketch of the house. Our CCTV planner helps you turn that list into a camera count, and our guide to where to place cameras covers the views in detail. The count tells you which kit to look at: the CCTV kits range is sorted by number of cameras.

2. Decide where the recorder goes

Every camera cable ends at the recorder, so its position sets the length of every run. Pick a spot that every cable can reach, with a mains socket close by and a screen or TV with an HDMI input within reach of the HDMI cable. If you want to view the cameras from a phone later, the recorder also needs a network lead to your router.

3. Choose PoE or coax wiring

This choice sets what you pull through the house.

  • PoE kits: each camera takes its power from the recorder over the same network cable that carries the picture. Our PoE kits, such as the 4-channel Hikvision 8MP set with 2TB drive, come with a 20m Cat6 patch cable for each camera. There is no power lead to run and no mains socket needed at the camera. Browse the IP (PoE) kits.
  • Coax kits: each camera needs a BNC video cable with a DC power lead, and the power comes from a power supply with a splitter that plugs into the mains near the recorder. Our 4-channel 5MP Hikvision coax kits come with a 20m RG59 cable with power lead for each camera. See the Turbo HD kits.

Starting from nothing, network cable is the neater route. If a house already has coax in the walls, check the cable and its connectors before you decide to reuse it. The two types do not mix: a PoE recorder takes network cameras and a coax recorder takes coax cameras.

4. Measure each cable route

Measure along the path the cable will really take: up the wall, along the loft or under the eaves, round corners and through the wall, not in a straight line. Add spare for the recorder end and for a loop behind the camera. The leads in our kits are 20m, so if a route is longer, ask us before ordering. The camera cable run checker is there to help with this. Do not stretch a cable past the length its maker rates it for.

5. Test everything before you drill

Put the recorder and the cameras on a table, connect them with the kit's own cables and a screen, and check that every camera shows a picture. A fault is far easier to find at a table than on a ladder. For a cable you have made or cut yourself, a cable tester from the testing tools range shows a broken or crossed wire before the cable goes into a wall.

6. Drill, run the cable and seal the hole

Hold each camera in place and check the picture on the screen before you mark the fixings. Check the wall for hidden pipes and cables before you drill. Drill the hole for the cable at a slight upward angle from the inside so that water runs away from the house, push the cable through, and fix the camera to the wall with suitable plugs. Seal the gap around the cable with an outdoor sealant and leave a small drip loop in the cable below the hole. Clip the cable along its route rather than leaving it hanging.

7. Connect the recorder and check the view

Plug each camera cable into the recorder, add the HDMI cable and, for a coax kit, the power supply, then switch on. Look at each live picture. The Information Commissioner's Office (ICO) says that where possible you should position cameras to capture only your own property. If a camera also captures a neighbour's property or a public area, data protection law applies, and you must put up signs showing CCTV is in operation. Read the ICO guidance on home CCTV systems and the GOV.UK guidance on domestic CCTV, and turn a camera if its view reaches next door.

Frequently asked questions

What is the first step in fitting CCTV at home?

Plan before you drill: choose the camera spots, decide where the recorder goes, and measure each cable route from the recorder to the camera.

Do PoE cameras need a mains socket at the camera?

No. In a PoE kit each camera takes its power from the recorder over the network cable, so only the recorder needs a mains socket.

Should I test the cameras before drilling?

Yes. Connect the cameras and recorder on a table first, so a fault is found before any holes are made.

How do I stop water getting in where the cable goes through the wall?

Drill at a slight upward angle from the inside, seal the gap around the cable with outdoor sealant and leave a drip loop below the hole.

Sources & references

  1. https://ico.org.uk/for-the-public/home-cctv-systems/
  2. https://www.gov.uk/government/publications/guidance-on-the-use-of-domestic-cctv/domestic-cctv-using-cctv-systems-on-your-property
  • installation
  • wiring

Written by

CCTV Kit Direct team